Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Just about everyone maintains their own individual idea on the subject of Installing A Bathtub.
Setting up a bath tub isn't precisely rocket science, yet it does call for strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open up a wall to get rid of the old tub as well as position the new tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. See to it you have actually qualified on your own for the task as well as are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider using one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This post will aid you install a brand-new bathtub in your shower room if you have actually already acquired a new tub as well as do not need to alter the plan of your previous water pipes.
Your devices and also product checklist ought to consist of the following:
Planning for the Setup
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to stop pressure on the tub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, position the bath tub in the required position. The wood boards are useful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the tub until the level reads level.
To set up faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the supply of water and also inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill the bathtub as well as also inspect the overflow electrical outlet as well as the normal outlet for leaks.
Finally, repair the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait up until the bath tub has actually been made use of a minimum of when as this will certainly settle it right into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap connectors. The former type needs to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, creating the water to pass through the wall surface in between the bath as well as the tiling, causing issues with moisture as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealer can split relatively early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that entry on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Enjoyed reading our write up? Please share it. Let other people discover it. Thank you for your time. Visit us again soon.
Sink issues? Connect. Report this page